Difference between revisions of "Making Paracord Falls"
John.cantin (talk | contribs) |
John.cantin (talk | contribs) |
||
| Line 11: | Line 11: | ||
===Weighted Fall=== | ===Weighted Fall=== | ||
Similar to the basic fall, the weighted fall adds a length of beaded chain inside the fall to increase its weight. | Similar to the basic fall, the weighted fall adds a length of beaded chain inside the fall to increase its weight. | ||
| + | |||
| + | The final fall will have three different thickness. | ||
For a 2' fall you will need an 8' length of ball chain and about 40" of paracord. Ball chain can be fed into one end of the paracord easily. Tie a piece of thread around to the end of a large needle. Tie the other end to the last ball of the chain. Feed the needle about 18" up into, and then out the side of the paracord. Snip the thread off tight to the paracord and allow it to slide back inside. The point where you brought the needle out of the paracord will be where the loop (center) is formed for your fall. Thread a permalock needle on the the shorter end of your paracord, then proceed like you're making a basic fall, by threading the paracord inside itself just above where the beads end. You don't want the beaded part of the paracord to be part of the loop for your fall, so give yourself about 1/2". | For a 2' fall you will need an 8' length of ball chain and about 40" of paracord. Ball chain can be fed into one end of the paracord easily. Tie a piece of thread around to the end of a large needle. Tie the other end to the last ball of the chain. Feed the needle about 18" up into, and then out the side of the paracord. Snip the thread off tight to the paracord and allow it to slide back inside. The point where you brought the needle out of the paracord will be where the loop (center) is formed for your fall. Thread a permalock needle on the the shorter end of your paracord, then proceed like you're making a basic fall, by threading the paracord inside itself just above where the beads end. You don't want the beaded part of the paracord to be part of the loop for your fall, so give yourself about 1/2". | ||
Revision as of 20:04, 23 May 2022
Paracord can be used to make falls in several different styles
Basic Fall
The basic fall is simply a piece of gutted paracord fed inside of itself to create a loop. The portion of the cord fed inside should be approximately 1/2 the length of the fall. This gives a slightly tapered profile to the fall by having 1/2 the fall doubled.
The final fall will have 2 different thickness.
Use a piece of paracord approximately 1/2 again as long as your desired final length. For example, if you want a 2' fall, use a piece of paracord 3' long. Attach a permalock needle to one end, thread the paracord back into itself 1 foot back from the needle. If possible pull the needle out through the bottom of the 2' section and snip off the melted hard end. If the cord is too tight and you can not get the needle out the other end, you can take the needle back out through the side of the paracord, snip it, and then pull it back inside.
Weighted Fall
Similar to the basic fall, the weighted fall adds a length of beaded chain inside the fall to increase its weight.
The final fall will have three different thickness.
For a 2' fall you will need an 8' length of ball chain and about 40" of paracord. Ball chain can be fed into one end of the paracord easily. Tie a piece of thread around to the end of a large needle. Tie the other end to the last ball of the chain. Feed the needle about 18" up into, and then out the side of the paracord. Snip the thread off tight to the paracord and allow it to slide back inside. The point where you brought the needle out of the paracord will be where the loop (center) is formed for your fall. Thread a permalock needle on the the shorter end of your paracord, then proceed like you're making a basic fall, by threading the paracord inside itself just above where the beads end. You don't want the beaded part of the paracord to be part of the loop for your fall, so give yourself about 1/2".
Twisted Taper Fall
Twisted taper falls use a partially gutted piece of paracord twisted and then fed inside itself.
For a 24" fall you will need about 40" of paracord with the guts still in it. Find the point that will be the loop of your fall (about 18" from one end) and make note of that spot (safety pins inserted to carefully avoid the inner core works well). Measure
1 2 2+strands in 1 2 full twisted
